Commutation failures are very frequent dynamic events in high voltage dc (HVDC) transmission systems. Commutation failure is mostly observed at the inverter side of HVDC links, where large firing angles are used. The minimum value of the extinction angle required for the proper operation of a valve is specified by the valve manufacturer; however, at the inverter side of HVDC systems the extinction angle is regulated to a value higher than the valve specifications to allow control adjustments ...
ABSTRACT The conversion of an input AC power at a given frequency and voltage to an output power at different frequency and voltage can be obtained with static circuits called power converters, containing controllable power electronic devices. Various power converters have been developed to fulfill the requirements of the wind power generation. The most common option for the generators used in wind power generation is “asynchronous”, because support for speed variations is provided. This ...
The power system is a highly nonlinear system that operates in a constantly changing environment; loads, generator outputs, voltage controllers, transmission lines, topology, and key operating parameters change continually. The behavior and output of the generators can be affected in a transient conditions. This transient condition can change the excitation and dynamics of the rotor which in turn produces undesirable oscillations of the system frequency and voltage magnitude. When subjected t...
ABSTRACT Industrial drive applications are generally classified into constant-speed and variable-speed drives. Traditionally, AC machines have been used in constant-speed applications and DC machines were preferred for variable-speed. Induction machine with drive systems are widely used in applications such as pumps, paper and textile mills, elevators, electric vehicle, subway transportation, home appliance and wind generation. The three-phase squirrel cage induction motor is the mostly used ...
Abstract Optimal capacitor placement is concerned with the optimal location of capacitors in a distribution system such that energy losses are reduced to a minimal value and the voltage profile and power factor of the system is improved. The reactive power can be controlled in order to improve the voltage profile and minimize the system loss. Generally, some load bus voltage might violate their upper or lower limits during system operation due to disturbances and/or system configuration ...
ABSTRACT A switch is an imperative constituent of any electronic or electrical circuit. It can either be mechanical, electro-mechanical or electronic. Mechanical and electro mechanical switches are prone to wear and tear with time. The introduction of semiconductors has led to the invention of electronic switches that are more efficient, fast and durable. Further development of electronic switches led to the production of touch-sensitive switches. This project is based on the design and const...
ABSTRACT Electricity companies typically possess numerous units and they need to commit unit because electricity cannot be stored in a large-scale system and demand is a random variable process fluctuating with the time of the day and the day of the week. A problem that must be frequently resolved by electricity utility is to economically determine a schedule of what units will be used to meet the forecasted demand, and satisfy operating constraints. Lagrangian multiplier method is one of the...
ABSTRACT Electronic Digital message display Board is an electronic gadget that is capable of displaying length of alphanumeric characters, symbols and any form of representation on a matrix of light emitting diodes (LED) scrolling the characters across the screen for information disemination. This project set out to solve the problem of inadequate clarity, objectiveness and degree of comprehension inherent in paper bill boards. Also, response to the information is further enhanced when th...
ABSTRACT This project work has covered the design of an automatic security lighting system for ATBU, Yelwa Campus. Requirements for illuminance, type of fittings, power dissipation and mounting height were put into consideration. An electronic model of the campus was built with the streets outlined and lamps fixed at positions along the streets according to the design. An electronic control, based on a Light Dependent Resistor (LDR) is built, which provides automatic switch on and switch off ...
ABSTRACT No one form of power can sustain a nation. The ever increasing demand for electrical power has arisen from our lifestyles with revolves around electric power to speed up processes of development such as manufacturing, service provision and general well being of man. The need for the provision of quick but minute energy to prevent the disruption of small but very important business or personal processes could be life saving promoting efficiency at all times. This project work goes thr...
Adding to the requirement and need for power supply for day to day activities, it is therefore a necessity to design the power system to maintain minimal technical losses in the network, because most of our system component lack sufficient reactive power ability, this mean that the penetration of distributed generation (DG) will give way to reduce the transmission and distribution system resources thereby increase the reliability and probably better the power quality at all time. Hence the ob...
Abstract In this project we designed a solar powered computer control system for electrical machines and spark ignition engines. It is made up of a hardware device that comprises of various electrical components which are powered by a 25W solar panel. The power cord of the machines are modified and connected to the hardware and the hardware is in turn connected to a laptop computer using a USB cord. The machines are controlled from the laptop computer using special software deve...
ABSTRACT This project is titled the construction of a DC to AC inverter system. It is constructing to meet up with the power demand in the offices and in homes in the absence of power supply from the power holding company of Nigeria, PHCN. In order words the device / item serves as a substitute for PHCN which almost monopolises the power supply to people. It is constructing in such a way that it will take up 12v DC from battery and inverts it to an output of 230v, 50Hz AC. It makes no noise d...
Abstract: Wireless power transfer system charging multiple devices, through inductive coupling method which is classified under near field transfer region. In this project, we intend to achieve wireless power transfer charging multiple devices such as mobile phone, toothbrush and other low end power devices without the use of conventional copper wire or cable between the transmitter module and receiver module. In t...
The energy generation and power consuming loads at Brass LNG facility located in Brass Island, Bayelsa State Nigeria were analyzed and compared with expected demand changes and means of minimizing cost and greenhouse gas emission were also proffered with wind and solar energy penetration into the overall power mix . The wind and solar hybrid power generation system reduced the fuel consumption, greenhouse gas emission and noise pollution by the generators and turbine by relieving some of the ...