Mechanical Engineering Research Papers/Topics

Microstructure And Mechanical Properties Of Epoxy – Rice Husk Ash Composite

ABSTRACT This study is about the production and characterization of epoxy-rice husk ash composite. Composites were produced at 10%,20%,30%,40% and 50% volume fraction of Rice Husk Ash(RHA) fillers and the epoxy was cast neat at 0%RHA which served as the control .The microstructure of the composites were studied with Scanning Electron Microscopy(SEM) and Energy Dispersive X-ray Spectroscopy(EDX).Mechanical properties of the composites such as tensile properties(tensile stress, tensile strain,...

A mathematical modelling of the intensity of contaminants (C02) on occupancy level of a space in continuous use

Abstract: This study investigates the Indoor Air Quality (lAQ) of a room apartment and focused on the number of occupants that a space or an apartment can accommodate as a result of increase in the concentration level of the CO2 contaminant present within the space. The law of mass action was applied to generate a relation between the concentration of CO2 produced and the concentration of the reactants (i.e., O2 and CO). A decay equation was also used to relate the variation in the number of...

Global Impact of Gas Flaring

ABSTRACT This work deals with the multi-faceted impact of gas flaring on a global scale and the different approach employed by researchers to measure gas flared and its resulting emissions. It gives an overview of methods employed by these researchers in the oil and gas industry, academia and governments in attempt to determine ways of measuring and reducing gas flaring and its emission drastically. This approach so far includes analytical studies, numerical studies, modeling, computer simul...

Energy Benchmarking And Carbon Footprint Reduction Opportunities In Portland Cement Manufacturing Processes In Nigeria.

ABSTRACT Energy benchmarking and carbon footprint reduction opportunities in Portland cement manufacturing processes in Nigeria are presented. Life Cycle Assessment (LCA) is used to estimate the environmental impact of three cement manufacturing processes in Nigeria. The energy consumption of the cement manufacturing processes are evaluated using energy Benchmarking and Energy Savings Tool for cement (BEST-Cement). BEST-Cement evaluates and compares the energy consumption of the cement manuf...

Effect of Antioxidants on the Performance Characteristic of A Diesel Engine Fuelled With Diesel And Jatropha Biodiesel Blends

Biodiesel is a clean-burning alternative fuel produced from renewable resources. However, it is susceptible to oxidative degradation due to autoxidation in the presence of oxygen, which hinders its widespread use. Antioxidant addition is a prospective solution to this problem. It is expected that antioxidants may affect the clean-burning characteristic of biodiesel. The aim of current study is to investigate the feasibility of biodiesel-diesel blended fuel of (30%, 35% and 40% biodiesel)...

Enhancement of Vehicle’s Security System

Generally the anti-theft security system becomes very important these days according to the high rate recording of the theft crimes cases around the world. In this project the vehicles security system type will be the focus of the study. The main objective of this vehicle’s anti-Theft Security System project is to design a smart security system to provide the highest level of protection to the owners of the vehicles or the authorized persons for unauthorized usage objects. In the resu...

Improvement Of The Performance Of Thermal Power Systems Through Energy And Exergy Analysis

ABSTRACT This research work is aimed at using the energy and exergy analysis with thermodynamic data to suggest improvements in the performance of steam and gas turbine power plants. In this regard, specific data from Egbin steam power plant and Geregu I gas turbine power plant were used for the analysis. In the analysis, scientific tools such as Engineering Equation Solver (EES) programme with built-in functions for most thermodynamic and transport properties was used to calculate the entha...

Computational Fluid Dynamics (CFD) Modeling Of Turbulence Induced Drag In Vehicle Aerodynamics

ABSTRACT This research work focused on the use of an hybrid RANS-LES turbulence model in simulating and checking the drag performance characteristics of an aerodynamic vehicle. The Spalart-Allmaras shear stress transport (SST)- Scale Adaptive Simulation (SAS) Turbulence model was selected for use, and with the help of OpenFOAM Finite Volume Computational Fluid Dynamic Solver the simulation algorithm was set and carried out in a total time step of 4000. Convergence was achieved under the stip...

Performance Analysis Of A Model Pulverized Coal Combustion System

ABSTRACT Performance analysis of a model pulverized coal combustion system is undertaken. The system consists of a hopper, screw conveyor, blower, electric motor, among others. The design and construction of the system focused on the following procedures in this work: The outlet of the pulverized coal from the silo opens directly into the receiving hopper of the screw conveyor. The drive of the blower is connected to the drive of the screw conveyor via bearings, pulleys, belt and gears. This ...

Analysis Of An Automatic Control System For Online Blending Of Petrol With Corrosion Inhibitor In The Direct Continuous Electronic Fuel Injection Automobile Engine

ABSTRACT This work analysed the performance of an automatic control system for the online blending of petrol with corrosion inhibitor in the direct, continuous electronic fuel injection automobile engine. The automatic control system was designed by superimposing a feedforward control system on a feedback control system. The design of the automatic control system was analysed by the method of direct substitution. The governing equations used in analysing the blending process, as well as the ...

Determination Of The State Of Stress Between Adhesively Bonded Single Lap-Joints.

ABSTRACT In this work, the state of stress between adhesively bonded single lap-joints was determined. The state of stress between adhesively bonded single lap-joints was determined by using a linear elastic analysis and experimental testing. In the analysis part of this work, the shear and normal stresses in an adhesively bonded single lap –joints were predicted by subjecting the joint to tension; shear force, and bending moments. Differential equations were used to model the problem and ...

Determination Of The State Of Stress Between Adhesively Bonded Single Lap-Joints.

ABSTRACT In this work, the state of stress between adhesively bonded single lap-joints was determined. The state of stress between adhesively bonded single lap-joints was determined by using a linear elastic analysis and experimental testing. In the analysis part of this work, the shear and normal stresses in an adhesively bonded single lap –joints were predicted by subjecting the joint to tension; shear force, and bending moments. Differential equations were used to model the problem and ...

Inventory Programmes In A Manufacturing Industry

ABSTRACT A working inventory model is developed to incorporate the partial back ordering inventory with references to the back ordering inventory model by Jonah and Chukwu. The re-order point models of maximum expected cost and service level approach were also established. Data, covering the demand, set-up cost, and the Holding cost were obtained from the Champion Breweries Plc, other related data were estimated. These enabled the application of the models to obtain, the review period, ...

Optimization Of Machining Parameters With Consideration Of Tool Adjustment In Turning Operations

Abstract Tolerancing in design stage and machining parameter optimization in manufacturing stage are related problems which have a great impact on overall production economics of a machining operation. Unfortunately, these problems have been viewed separately causing conflicts between design and manufacturing decisions. While a design decision is to attain a certain part tolerance in the manufacturing stage, the manufacturing decision may be more concerned about economical production and prod...

Fractal dimension and time factors of sawdust pattern formation in sawmills

Abstract: This paper presents the application offractal theory, especially fractal dimension to the formation of sawdust particles during operation with four detailed cases, which helps us to understand the distribution of the sawdust particles inhaled by sawmill workers and remove the effect of toxicity on their body quickly. Pattern of formation of sawdust in human lungs and other parts of the body (in fast branching rate) is described with a practical case study in a developing country. A...


166 - 180 Of 623 Results